FOLDD-LCD-DISPLAY
TRIPPER ELECTRIC BIKES

FOLDD-LCD-DISPLAY

Regular price $29.99 Sale price $49.99 Unit price per
Shipping calculated at checkout.

 

Tripper Foldd low step and Foldd high bar -LCD5 style eBike Display User Manual V1.0

Dear customer, please read this manual before you use KT-LCD5 instrument. The manual will guide you use the instrument correctly to achieve a variety of vehicle control and vehicle status display. Functions and Display

Operation

1. ON/OFF

Hold button long to turn on the power, and hold long for a second time to turn off the power. When the motor stops driving and when the e-bike is not used for a consecutive 5 minutes, it will automatically shut down and turn off the motor power supply.
2. Display 1

2.1

Turn on backlight and headlights

2.2

2.3

2.4

2.5

2.6

2.7

Hold long to turn on backlight and headlights (the controller should have headlight drive output function); hold long again to turn off the backlight and headlights.

Assist ratio gear (ASSIST) switch

Hold or shortly to switch 1-5 file gear. Gear 1 is for the minimum power, gear 5 is for the highest power. Each startup will automatically restore the gear shutdown last time(the user can set randomly). Gear 0 is without booster function.

6Km/H assist promotion function

1

UP Button

11

Km/H

Riding speed(

metric)

2

SW Button

MPH

Riding speed (

imperial)

3

DOWN Button

MXS

MAX speed

4

ASSIST

Pas level

AVS

Average speed

5

Battery capacity indicator

12

Km

Distance(

metric

)

6

CRUISE

Cruise function

Mil

Distance (

imperial

)

7

PAS

Power-assisted function

DST

Trip distance

8

TM

Single trip time

ODO

Total distance

TTM

Total trip time

VOL

Battery voltage

9

THROTTLE

Throttle display

13

The brake display

10

6Km/H push power assist

14

Backlight and headlights

THROTTLE display

PAS display

Cruise function

Hold and flashes, the vehicle drives at the speed not more than 6Km /h. Release button, the function is invalid.

Turn on throttle, THROTTLE display.

When Power-assisted riding, PAS display.

After the cruise function is turned on, the trip riding speed is greater than

button to cancel. Display and delete of single Data

7 km/ h, hold

long and enter cruise, the CRUISE lit. Brake or hold any

Hold button to start up and enter display 1.

  1. Display 2

  2. Display 3

After power on for 5 seconds, hold and at the same time, single trip riding time (TM) and single trip distance (DST) flash, hold button shortly, the content of both is cleared. If failed holding the button within 5 seconds, it will automatically return the display interface after 5

seconds, original content is preserved.

Hold button shortly in display 1 to enter display 2. In the riding mode after 5 seconds, display 2 automatically returns to display 1.

Hold button shortly in display 2 to enter display 3. In the riding condition, five seconds later, a single maximum speed (MXS) display automatically returns to the real riding speed (Km/H).

3. Set the metric units

The wheel diameter will be set after finishing setting the maximum riding

speed, wheel diameter specifications flashes. Hold or shortly to set the specifications of wheel diameter. Select the range 6,8,10,12,14,16,18,20,22,

24,26,700c and 28 inches. Hold button shortly and go to the next parameter settings.

The metric units will be set after finishing setting wheel diameter, Km/H

and Km flash. Hold or shortly and select the three metric units of speed, mileage, and ambient temperature in synchronization.

Display

Metric

Imperial

Riding speed

Km/H

MPH

Total distance

Km

Mil

  1. In display 3, hold button shortly (SW),and the display will re-enter display 1.

  2. Hold button to turn off the display and the power supply of controller.

  3. Automatically prompt interface

4. Km/H and Km stop flash after metric unit setting is completed. Hold button shortly again to re-enter the maximum riding speed setting interface; or hold button long to exit from setting environment of routine projects and save the setting values, returning to display 1.
5. Exit from routine project setting

All three routine project settings can exit from the setting environment and return to the display

if hold button long after each setting is completed, meanwhile the setting values are saved. Under each setting interface, if the button failed holding for more than 1 minute, it will

automatically return to display 1, and the setting value is invalid.

7.1 Error Code Display

Error Code
01
_info Throttle Abnormality
03
_info Motor hall signal Abnormality
04
_info Torque sensor signal Abnormality
05
_info Axis speed sensor Abnormality(only applied to torque sensor) 06_info Motor or controller has short circuit Abnormality

Definition

Electronic control system failure will display (flashing) fault code. Once the fault was removed, it automatically exits from the fault code display interface.
General Project Setting

  1. Set maximum riding speed

    After power on for 5 seconds, hold and at the same time, maximum riding speed Km/H and MXS flash, hold or shortly to set

    the maximum riding speed (default 25Km/H). Hold button shortly and

    go to the next parameter settings.

  2. Wheel diameter setting

1.

2.

Dimensions of main instrument body

Wiring diagram

Outline Drawings and Dimensions